In stock
  • ALKO Sensabrake Pressure Bleed Gun Hydraulic System Trailer Caravan Boat 350045

    $74.75

    var itemNumber = window.ebayItemID ? window.ebayItemID : -1; function passpara(){return '&id=1439616&itembgcolor=0xFFFFFF&bordercolor=0x000000&storewindowbgcolor=0xf1f1f1&toptextcolor=0xFFFFFF&bottomtextcolor=0xFFFFFF&stripcolor=0x006ab1&auctionclosemessagecolor=0xff0000&emptyboxmessagecolor=0xFFFFFF&buttovercolor=0x660000&buttoutcolor=0x00000AA&searchtitlecolor=0xFFFFFF&searchbuttbgcolor=0xc0c0c0&searchbutttextcolor=0x000000&searchbuttbordercolor=0x000000&itemhighlightcolor=0xfff000&navbuttonactivecolor=0x000006&navbuttonoutlinecolor=0xff9900&navbuttoninactivebgcolor=0x000000&siteid=15&cat=159191&item=' + itemNumber + '&baseurl='+escape(location.href.substring(0, location.href.lastIndexOf('/') + 1));} function passparaSC(){return '&baseurl='+escape(location.href.substring(0, location.href.lastIndexOf('/') + 1)) + '&sitebaseurl=http://www.auctiva.com&tagNum=1';} ALKO Sensabrake Pressure Bleed GunBleeding the Hydraulic SystemBleeding instructions using Sensabrake? Pressure Bleed Gun??1. Fill reservoir with clean brake fluid to just below the top of the sight glass.2. Place the pressure bleed gun socket gently over the neck of the reservoir applying gentlepressure to locate the bleed socket in place3. Screw the lid in place to secure the socket.4. Do not push on with excessive force or damage may be caused to the reservoir or the 0 ringon the pressure bleed gun socket.5. Place the other end of the bleed gun tube into a bottle or container of fresh, new brake fluid.6. Open the bleed screw (start with the furthermost calliper) at least one full turn. Place a clearflexible hose over the bleed screw and immerse the other end into a container partially filledwith brake fluid.7. Squeeze the pressure bleed gun repeatedly (but not too fast or cavitationsmay occur) ensuring that the bulk brake fluid tank and the reservoir do not run out of brakefluid or air will enter the hydraulic system. At no stage let the fluid level in the reservoir fallbelow the minimum fluid level indicator.8. Continue squeezing the pressure bleed gun until the brake fluid in the flexible hose attached to the bleed screw is free of air bubbles and tighten the bleed screw.9. Repeat the process with the next furthermost calliper away from the actuator.10. Bleed the other side of the trailer starting with the closest calliper to the actuator first as above11. Connect the trailer to the tow vehicle and turn on ignition to activate actuator. Allow the compressor to fully charge the actuator (approx 90 seconds). Once the compressor has stopped apply the brakes, and hold on for a 5 second period and release. Repeat this 4 times.12. Check the brake fluid level in the reservoir. It should not exceed the top of the sight glass maximum level.13. Replace the fluid reservoir cap.??IMPORTANTBefore removing the pressure bleed gun from the reservoir, make sure that there is no pressure in the system (pressure bleed gun has fully returned to the rest position) or brake fluid spillage will occur causing paint damageWARNING:Correct bleeding of the actuator is critical as trapped air greatly reduces the efficiency of the brakes. When the bleeding process is complete, check all bleeder screws to ensure that they are secure and do not leak.Failure to properly install, operate and maintain your Sensabrake? braking system can cause malfunctionresulting in possible serious or fatal injuries and/or property damage.Monitor the brake fluid level in the reservoir so that the actuator is not run without??To prime the bleederTurn the dose adjuster to 12.5ml position. Hold the applicator vertically upwards and prime by squeezing the handle completely forward until all air has been expelled from the tubing and bleed gun.To lubricate the bleederThe bleeder has a unique lubricating felt washer enabling the barrel to be lubricated after each use. To relubricate the felt washer, remove the barrel and dip the piston (o-ring and felt washer) into brake fluid.N.B. Do not use mineral based oils such as CRCWARNING -Failure to bleed the Sensabrake? actuator according to manufacturers instruction may cause equipment damage and void the product warranty.Under no circumstances should the Sensabrake? actuator be used to bleed thebrake system.WARNING -The bleeding device is not designed to withstand extreme pressurization so should never be pumped continuously without at least one brake bleed screw being in an open position. Failure to observe this warning may cause the bleedgun to fail, and possible property damage may occur through brake fluid contamination!WARNING -The end of the bleeding device hose not connected to the Sensabrake? should always be submerged in a bottle of clean brake fluid. Failure to follow this procedure may result in air being pumped into the brake system and the full bleed procedure needing to be repeated.ALKO--QUALITY FOR LIFEEasy to installHundreds of stock on hand wholesale availablePostwith Register NumberNEVER BEATEN ON PRICELOWEST PRICE IN AUSTRALIAPowered by eBay Turbo Lister

    Reviews